For any of you who follow my blog it should be very apparent how impressed I have been with the Saberstrip v2.0 which uses the Godox/Flashpoint 200ws strobe instead of a speed light like their SS v1.0. A few years ago I was very fortunate to test their new prototype and gave them some feedback about the unit. It was very minor and I anxiously awaited the final release. And waited, and waited, and….well you get the picture.
I used the v2.0s during many different sessions, but I found they worked so well for my studio dance imagery they became my defacto lights for dance. You can read about my impressions and experiences in my post about the Saberstrip v2.0.
Recently a visitor to my site made me aware of a similar light modifier by Strobius, their StrobiStrip 100. I also found another modifier the FOTOCREAT 3″×20″(8×50cm) Strip Flash Diffuser Softbox on Amazon. So I purchased one of each to see how they compared to the SSv2.0. Both of those units are designed to be used with speed lights, but since the 200 is close in shape and size to the end of a speed light I figured they’d fit the 200. And they do indeed.
Both the Strobistrip and the Fotocreat are very similar in materials and design. Both use a rip stop translucent fabric as diffusion material, ballistic nylon for the body and silver fabric to reflect light on the interiors. Velcro attaches the tube together as well. The Strobistrip differs as it uses a semi rigid piece of clear plastic to keep the shape of the tube consistent and I imagine more evenly reflects light throughout the tube. Because it breaks down it’s a very clever design.
StrobiStrip 100 with the clear plastic installed.
I’m a firm believer that you never get something for nothing. The SSv2.0 is a remarkable modifier but it is bulky to carry since it is a solid tube. The other two are much smaller when packed down. About the size of a man’s travel bag for his toothbrush, shaving kit, etc. So trading portability for size, I assumed that the light output would not be the same. So I tested all of them.
StrobiStrip 100 packed compared to my Fuji X00V for size.
My Testing Chart of all three Modifiers
As you can see the SSv2.0 has the most consistent and efficient use of the light. The StrobiStrip 100 was less consistent and efficient than the SSv2.0. The FOTOCREAT was all over the place in terms of its light output along the length of the tube. I returned the FOTOCREAT as it is too small for my work and the inconsistent light output along its length made it unattractive for my taste.
In examining the interior of the SSv2.0 he follows the same design as his v1.0 unit. A very cleverly placed piece of ramped reflecting material at the opposite end of the strobe’s socket must increase the light furthest from the source to make it so even.
Interior of the SSv2.0
I also feel that the StrobiStrip’s use of clear plastic to help hold the tube’s shape also adds to the interior’s reflective value helps with its light efficiency and consistency.
Interior of the StrobiStrip 100
One of the most ingenuous design elements of the SSv2.0 is how it mounts the AD200 to the tube. He has developed what I refer to as the ‘tractor tire’ with a 3/8” peg that will fit into any standard light stand socket. The tube rotates around the tractor tire giving me the ability to easily adjust the direction of the diffusion fabric. I’m not talking about your normal x/y adjustment, but the z axis without disturbing the other two axis’s.
I have come to depend on that wonderful design feature. So when I tried to use the Flashpoint eVOLV 200 Round Flash Head attachment on my eVOLV 200 with the StrobiStrip in hopes that it would allow it to smoothly rotate around the strobe I was thrilled! There is enough Velcro to still securely attach the modifier to the strobe, but with the round head, it allows a smooth rotation around the strobe! The OEM Fresnel head does work as well, but the round head is much better to use in rotating the modifier.
Very convenient that the Round Head is just flush with the beginning of the StrobiStrip’s diffusion fabric. The swivel I use stops the tube from going further down the strobe too. Slick!
In the following two images you can see that I can rotate the modifier around the strobe which is one of the features of the SSv2.0 I fell in love with.
Enough Velcro to secure the modifier around the 200 with the Round Head attached.
I wanted to determine if the StrobiStrip 100 holds up to high wind as well as my SSv2.0s. Yep they do just fine. The modifier is around 5-11 up in the air on a light stand.
I will keep an eye on the StrobiStrip fabric which is wrinkled when assembled. I doubt it will pose issues in the quality of light. If so I will report back here.
I have used my SSv2.0s so much that one of the tubes has started to split, so I just used gaff tape to repair it. The other one’s diffusion fabric started to fray so I used some superglue on it. IF Saberstrip ever decides to manufacture them I will be first in line. But until or IF they do and I need more tube modifiers I’m glad to have been made aware of the StrobiStrip 100s. I keep mine built and will break them down once COVID19 is over and I have to travel for work again.
If you want to try tube modifiers with an AD200 they are the ones I recommend.
I have found an alternative to the SSv2.0 which you can view here.
November 27 2019
I am very sad to report that I can no longer recommend the SaberStrip v2.0. I have attempted to contact Scott the owner of SaberStrip to no avail. Not even a peep. My feeling is ignoring an email or Instagram message is not acceptable or polite. A visitor to this site had written to me since he had ordered a v1.0 SS and never heard back…until he asked for a refund. That was promptly answered.
Sad since it’s a great modifier, but when something cannot be purchased it becomes vaporware. When I find an alternative I will post it to my blog.
January 13 2019
I continue to be absolutely amazed at the flexibility and versatility of the v2.0 Saberstrips. As of this writing I do know that Scott has not yet offered these for sale to the general public. The reason I continue to post my findings here is in hopes of motivating some of you to contact him to ‘hurry him along‘ in the sale of these modifiers. In addition to dance, their form factor and quality of light make them invaluable in my tool kit. Seriously – combined with the AD200 strobes I feel they are a revolution in modifiers. Here are just a few of the in studio dance imagery created using these lights.
An AD200 is the strobe.
My general configuration of the v2.0 Saberstrips for this session. The converted Fresnel and the 69″ Elinchrom I have converted to a focusing rod modifier are actually used for FILL, not as key lights for this dance session.
Update November 19 2018
I continue to be so impressed how using two v2.0 Saberstrips can produce the light I so love which could only be created with a ring light. But the huge difference is since the lights are NOT attached to the camera, I can use a long lens, yet keep the lighting near the talent. This was taken with a Canon EF 85mm f1.2 lens. The versatility of these modifiers is incredible.
Not to mention my use of them in dance imagery creation.
Several of you have written to me asking when Scott will release these modifiers. I highly suggest you write to him on his website to ask. I continue to encourage him to release these modifiers.
Update October 14 2018
I recently conducted a studio dance session using three Saberstrip v2.0s combined with a Mole Richardson Fresnel spotlight I have converted to a strobe. I continue to be so amazed and impressed by the versatility and light quality of the second generation Saberstrips. As I’ve stated before I’m just scratching the surface of what can be accomplished with these remarkable lighting tools.
My general placement of the SS’s for the dance session. I am able to control on/off levels using my R2 controller. The ability to place the hair/rim light so close to the ceiling is remarkable.
Here you can see my general placement of the Fresnel spotlight which has been converted to a strobe which uses a Flashpoint 1200ws head.
Each of these images were created using a combination of Fresnel/Saberstrip light modifiers.
Update September 17 2018
Yesterday I conducted an all day dance session. I found that utilizing three v2.0 Saberstrips with 3 Flashpoint AD200s produced remarkable light for studio dance. Rim lights, using two Saberstrips and one overhead light produced the exact mood I was trying to achieve. Seriously this combination is incredible for my dance work.
How I configured the Saberstrips for the dance session.
Update August 1 2018
I recently used the v2 Saberstrips in on location sessions in Seattle. Man I could not have done it without them! You can read about it here.
I have also completed a publicity shoot using two Saberstrips for a West Side Story publicity image as shown below.
Two v2 Saberstrips in parallel to the ground. I just love the look of this light configuration.
Like most other folks and way before I began shooting as a full time pro, I had a day job. It was during this time I discovered a very unique light modifier called the SaberStrip. What was so intriguing to me is its shape and the quality of light it produces. I was a bit suspicious when I first received my Strip because it seemed like ‘just a high quality shipping tube’ with some rip stop nylon as the modifier’s cover. Also this was back in the day when I was almost exclusively using speed lights, but had two PCB Einsteins for my ‘studio work.’ And this was well before the advent of built in radio receivers in speed lights, so I had to use a pigtail cable connected to my speed light inside the tube to attach it to the Phottix Transmission receiver I was using at the time. A bit of a hassle, but it was the only thing that existed at the time, which was ‘high tech’ for that era.
Although I loved the quality of light it produced, for me the power or rather lack of power of the speed light relegated the Strip to my closet. I tried to fabricate my own ‘Strip’ for my Einsteins, but found out it was not as easy as I thought. So I basically gave up and moved on to other things.
In 2013 I decided to create a series of images about the hands of artists which included both performing as well as creating artists. Since I wanted to shoot the talent in their natural environments I found that all of my ‘normal’ modifiers would not work well due to space. In some cases I had literally 10 inches or less to place a light and modifier to light the talent! So as I was rummaging through my gear closet I happened upon my Strip that I had doomed to its lonely existence in the back of my modifier closet. Eureka! That’s the perfect tool for this job and since most of the venues I was shooting in were very small I would not need a ton of light power so my speed light would do just fine.
By happenstance the Director of the Peninsula Museum of Art saw one of my images and asked to see the rest. She then asked if I’d consider having a solo exhibit at the museum the following year. I politely told her no and when she inquired as to the reason for my decision I simply replied “I don’t think my work is good enough for a museum and I think it would be very narcissist to do that.” She simply smiled and said OK. Later one of the artist I know mentioned that he had heard I was offered a solo museum exhibit but turned it down. Werner asked me if I ever go to museum exhibits to which I responded “Why yes, I love going, why?” His response was typical Werner, direct and to the point; “Well quit being so fucking selfish and let others enjoy and be inspired by what you’ve created Mark!” I’m seldom if ever at a loss for words but I had nothing to say. So I contacted the Director and agreed to display my work which I titled “29 Hands, 15 Artists.” With the exception of one of the images, all were lit with my Strip and a speed light.
Fast forward to today, 2018 and I was made aware of SaberStrip’s v2.0 version of the Strip which accepts an eVOLV200! In March 2018 I was shipped two advanced copies of the modifiers to test to see if I could offer any feedback. Here’s what I’ve found so far:
The 200 is inserted into the bottom of the modifier through what I call the “Tractor Tire” the designer fabricated it to attach the 200. I believe his design is to offer strength to the mount. I simply like to think he liked Tonka Trucks as a kid! The knurled knob on the left in this photo is the turning knob that screws the 200 in place. The other nice design feature is you can eject the battery of the 200 without removing it from the modifier, a very thoughtful design element.
Sorry for the shitty camera phone blurry image. The red thing you see at the top of this shot indicates that the screw is NOT attached to the 200 which is a very nice feature. One of the things that I found to be a design issue, it’s very easy to over tighten the screw. There’s no need to do so because it makes it VERY difficult to unscrew the unit from the mount. I learned the hard way and had to use a screwdriver and hammer to loosen the screw.
It’s also not possible to let the eVOLV slide down into the tube because there are ribs on the interior which keeps the strobe from sliding too far into the unit. I believe he may have other plan since those interior ribs seem to be reinforcements for four exterior metal nipples. Barn door or grid accessories for the future? Perhaps.
I painted a directional arrow on the housing to indicate which direction to loosen the mounting screw.
What the interior looks like in the v2.0 Strip. You can see the reinforcing supports which prevent the eVOLV from sliding too far into the tube.
Although most people will not have to do this, I ground down the mounting peg that is cast into the housing. This allows me to easily insert the peg into female mounts I use to place the modifier in either a vertical or horizontal position. Although the v2.0 Strip works extremely well in stands which offer the mounting peg to be in a vertical or horizontal position, not all light stands offer that option. When I travel to other cities I often have to rent stands and not all rental houses have adjustable spigot locations on their stands.
This is why I needed to shave down the diameter of the molded peg. It would not fit as cast. I find these female spigots invaluable in my gear bag.
I plan to use these to mimic a ‘ring light’ because I can now leave the modifier and strobe very close to the talent and back away to shoot with a long lens. Not possible with traditional ring lights. Also since the eVOLVS have modeling lights in the Fresnel head I now have a modeling light in this configuration. Sure, not brightest modeling light, but way better than none.
My first test was with Bob outdoors for a ring light style lighting test.
Canon 1DXII EF135 lens ISO 100 both AD200s set at 1/8 power. 1/5000th f2.0
Canon 1DXII EF135 lens ISO 100 both AD200s set at 1/8 power. 1/8000th f2.0
In those instances where I want to place the v2.0 Strip close to the ground I will simply use a Godox S bracket as a base. This configuration will be perfect for dance shoots as fill lights or anytime you wish to place the units very low onto a flat surface.
w/2 eVOLVS and SS
Flashpoint Zoom R2
Distance to Sekonic
Time to Recycle
Length of fabric
Width of fabric
Length of modifier
Diameter of modifier
For me the most significant stats are the recycle time and power. It’s the very reason I stopped using my original speed light Strip, it just lacked power. And in my work a one second delay feels like 12 years. Human expressions change in a nanosecond and invariably it’s the money shot I wanted, but missed because the strobe was recycling. Two full stops and five seconds faster in recycle time makes this modifier an incredible tool.
The ‘tube’ freely rotates around the mount so it can easily and conveniently turn the fabric to any position needed. There’s also a very small 1/4 inch 20 screw hole in the ‘tractor tire’ housing. I’m not sure why the guy put one there but it’s damn convenient. I plan to place a female mounting stud in there so I can either mount the Strip with the built in male stud or a female one. It should be noted that if you place a long ¼ 20 screw into that hole it will stop the free rotation of the tube. So IF you are the anal type and want to lock down the tube’s rotation you can do that with this screw hole.
This coming weekend I have three personal project shoots and I plan to test the light quality and applications in those sessions. I’m not sure how many times the Strip v2.0 will be my key light, but now that the recycle times and the power available through this meets my needs I’m sure it will always be in my bag.
The number of ways to mount the Strip seems endless. My current favorite grip mount for the Strip is the Matthews Mini Grip Head. I modified it by drilling out one of the holes to 9/16th of an inch which fits the Strip’s 5/8th inch stud.
What I like:
High quality Construction
Built in male mounting stud
Ability to rotate the modifier around two axis
Accepts the Evolv200
Well balanced, having the strobe at the mounting end of the modifier
Very wind resistant
Will fit into very tight spaces
Male stud needs to be the 5/8th inch size standard of all spigots
Wheel that attaches the strobe needs to have directional arrows.
Wheel needs to prevent over tightening
During the weekend of April 21st 2018 I had my first opportunity to use the v2 Sabers in studio. I wanted to determine if paring them in a horizontal way would give me the ring light type of affect. I’ve always loved the look of a ring light shot, but have been frustrated that the distance of the light to the talent is limited by the focal length of my lens. Using my ring light further away to compress the talent’s face meant that the light is also further away, causing a harsher look. But using two Strips horizontal to the ground with the ability to adjust the distance between them allows me to leave the light source close to the talent, yet move further back to use a longer focal length. Having my cake and eating it too is wonderful!
The images below show how this worked on Jessica and I’m very happy with the results. Shot with a 135mm prime lens.
The flexibility of being able to angle the pitch of the Strips and distance between them is wonderful. More control than a ring light. As a fill/rim light I have not experienced a better modifier. Reflectors make great fill or rim light modifiers, but I have always preferred strobes for that task. It allows me finer control of my fill light.
By changing the angle of the top Strip in the image of Jess with her arm above her head I am able to cast a bit of a shadow on her eyes while filling in under her eyes to prevent shadows. That flexibility allows me to create nuance shadow/highlights with the Strips.
Here I am using the Strips as a fill and rim light. All of these images are three light shots. My 10” Fresnel is the key light, a gobo modifier is used on a light to create pattern on the background and the Strip is used as a fill/rim light.
The control of the Strip as a fill light is quite lovely and can be used as subtle or as bold as you wish. Here are two more images I created using two SS’s in parallel as a ‘ring light’ but in my view with a much better result.
Erica is 50+ and just the use of a shallow DOF and the two SS lights produced this image WITHOUT the use of Photoshop.
Two SaberStrips v2.0
Three SaberStrips v2.0
Oh and large groups in moderate to strong wind? I was recently at a client to cover the high school musical awards and prior to the event kids assemble outside. It’s often a fun place to get group shots before the show. The issue is always crowded sidewalks and of course crazy high school kids. I shot this image with ONE SS and one eVOLV200 at HALF POWER.
1/100th f5.0 ISO100, SS v2 is the modifier and the strobe is the AD200 set to half power. Can you say incredible? It’s crazy.
I recently visited Luna Cycle in El Segundo to do some documentary photography of the staff. In the vast majority of cases the SS were used due to their flexibility and light quality. As in my 29 Hands Exhibit I was able to use the SS to light the talent in places where it would be almost impossible to fit a modifier in the space I had available and achieve a quality of light I wanted. Below is an example of one of the shots.
This is the ‘natural light’ scene where I was to photograph one of the young ladies who performs logistics for Luna Cycle.
Removing some of the boxes and shooting the light through the bookcase produced the image and quality of light I was after.
My apologies as I know you won’t be able to ‘unsee’ the image that follows, but to date it illustrates the rim lighting capabilities of the Strip. During this session I was to shoot two Drag Queens. The fella on the left is 6-1 without heels and with his 4” heels it makes him 6-5! I used the Strip as a rim light and if you notice the illumination from head to toe it’s quite remarkable. Could this be accomplished with a gridded light? Of course it could. But due to the very slim shape of the Strip it allowed me to get as close to the back drape as possible keeping spill to a minimum and certainly much less than a softbox without a grid.
Outdoors with the Strip is quite good. It is ‘almost’ impervious to wind, high wind. It is more wind resistant than my go to outdoor modifier, the PCB Omni. The disadvantage is since the Strip uses the AD200 it is a full stop less powerful than the AD600 I use with the Omni or my Aputure Fresnel head. But to circumvent that disadvantage I often use two Strips as a key light when outdoors. And in those instances where I want a very large light source I use three Strips configured in a Y shape. I find it’s the equivalent to a 45” octa with 600ws of power. Ever use something that size out in moderate or high wind? And I use all three on a single stand.
My partner recently conducted a head shot session using two of the Strips. She used one as the key and the other as a rim light. It was very windy under the concrete bridge where she was shooting and the Strips barely wobbled. The light quality is excellent and easily replicated her preferred modifier, a Glow 36” Octa. But in that kind of wind, especially the gusts that occurred an octa would have been quite the handful. She does prefer the catch light of the octa, a personal preference to which many people may agree. I happen to feel that round catch lights are the default, yet in natural light a catch light is anything but round…..
As you can see the quality of light produced by the Strip is excellent. Two lights, both Strips. One as the key light the other as a rim light.
Is it the perfect modifier? Nope, but as of right now there is no perfect modifier. Just like there’s not a perfect camera, lens or person. Is it the most versatile modifier I currently own or use? YES! For me the v2 Saber Strips are revolutionary and I have not even scratched the surface of how they can be used. Thank goodness for the AD200 lights and Scott’s development to incorporate them into the Saber Strips! Scott has mentioned that the v2 versions which use the eVOLV200s will be available in late July 2018.
Whenever I am hired by a client to create imagery my first question is always “What is the mood you’d like me to create for this session?” Sometimes they have a mood board established, sometimes not. The reason I tend to shy away from mood boards, meaning photographs; it is human nature to get a specific shot stuck in our heads. Much like those crazy M.C. Escher drawings where there are two distinct images, but once you see one, you have a hell of a time seeing the other. And since the client wants their marketing to stand out from what has been done in the past, photocopy photography (my term) just isn’t something I’m hired to do, nor do I want to do that type of shooting.
My beloved Mole Richardson Fresnel that I converted into a strobe is one of my most treasured light modifiers.
I almost always assemble all of my modifiers prior to placing them. Space as you can see was tight on this space.
We let the MUA borrow one of our LED lights and modifiers so she could apply makeup in the temperature of the light we were using.
General blocking of a shot is time consuming.
So the stage play “Nine” is based on the 2009 movie of the same name. The client wanted a Vanity Fair look and feel to the images which would all be in black and white….my favorite color btw! Since this is a new client for publicity I did not ask questions like, “How do you want the imagery to smell, taste and sound?” Crazy imagery questions right? But imagery, much like music is just the catalyst to begin a sensory process that takes the viewer into feelings, dreams and memories of their own. It is the reason why I judge imagery by how I feel when I gaze upon the vision. A pretty picture without feeling is just a pretty picture for me.
Poster for Nine the 2009 Movie
Although I would be creating imagery of each individual character, the money shots would be of the group together, nine people in total. For anyone who has shot groups, you know very well the challenges it produces. My situation was no different. Sculpting light for a group of people takes finesse and planning.
The Glow Grand Para 70 is a REMARKABLE modifier. It has taken me six full months to begin to understand how to effectively use this beast. Unlike other focusing rod modifiers its most compelling use is not for the faint of heart, just like the Bron 133 Para line. BUT once I began to understand the nuances of its characteristics it has become my go to modifiers for many, many sessions. In its fully flooded focusing rod position it easily covered the entire group of 9 people. And unlike normal diffused soft or octa boxes, the color punch and contrast is delicious. My client base has been convinced of focusing rod modifier results.
With a group this large and arranged in the way the client wanted, a very large fill/rim light was needed. This is where I used my Elinchrom 69” with my focusing rod fully flooded. For directional fill I used the Glow EZ with the inner disk/diffusion panel and the grid to direct the fill to where it was needed.
The ability to focus or flood the Glow Grand Para and the Elinchrom 69” is wonderful. Focusing rods replace my need to haul and lug many different sizes and types of modifiers to obtain the characteristics and feeling I am trying to achieve in light. And as I’ve stated earlier, the light they produced when used properly is just exquisite.
As just an example:
This shot of Steve was created with the Glow Grand with the rod in its fully focused position. His ‘scream’ needed to have a spotlight affect the client desired. So instead of having to change the modifier to a ‘spot’ type or apply a grid I just adjust the position of the strobe in the modifier.
In using the Eli 69” as a fill I was able to either fully flood the modifier or use more of a spotlight fill in the situation where I wanted more of a pinpoint for fill. With a group this large that is a godsend. I also used my Mole Richardson as a subtle hair light in those instances where I wanted a glow on the person or persons hair.
The Saberstrip v2.0 which uses an AD200 rather than a speed light is just as remarkable as either a key light, rim light or both. I’m still not sure where Scott is in offering these to the general public, but if and when he does BUY some! LOL I cannot speak highly enough about these unique and incredible modifiers paired with an AD200.
I often find that using gobos to project light patterns on a wall, ceiling, floor or drapes adds more texture and mood to a shot. In this case I asked the client to pick the window gobo she wanted for this mood.
I used a light amount of cold haze to soften the light and the complexion of the talent. Subtle haze is something often used in film and I love how it affects the mood of a shot as well. It adds a very cinematic feel to the shot. I use a cold hazer rather than one that heats the fluid. I find the particulate much more fine than heated haze fluid.
People always get so nervous when they see how I hold my cameras! I hate straps. LOL!!!
Shooting as a pro means there are times when you have to prove yourself once again with an established client. Not doing a great job either in the finished product or through your service simply means you’re not used again. One of my long standing clients, Village Theatre recently changed Artistic Directors. Jerry Dixon, their new AD planned to attend two of the three on location publicity shoots all to be held in different cities in greater Seattle area. The first session for the play Curious Incidents is also the play he is directing. No pressure eh? LOL
The second aspect of this day that is always a bit concerning was that I NEVER SAW ANY OF THE VENUES IN ADVANCE of the day! Sure the Marketing Director sent me some camera phone photos and links to the MOPOP (Museum of Pop Culture) areas where she wanted to shoot, but I had never been there. Nor had I been to Spangler Book Exchange/Reread Books, the quaint bookstore where we were to shoot the Matilda publicity or the alley in Everett where I’d shoot the Howard Barnes publicity. Add to that the additional element of time. For each venue we were limited in time based on either the schedule of some of the talent or due to the venue’s prior commitments.
The only element I ever insist on from clients is to answer; “What is the mood you want from each session?” Why? Well because the expression of the talent(s) and the LIGHT is something I have to plan for BEFORE I hit the job….which leads me to….
The Marketing Director kept asking me “Mark, I need to know your power requirements for each venue so I can work with each of the operations managers to plan power for your gear.” Since I exclusively use Flashpoint strobes, guess what….they need no outside power!!! SCORE! I hauled seven, yes seven strobes from SF to SEA in a small Pelican case. 49.5 pounds…just UNDER the 50 lbs. limit! Three Xplor600s, one 600Pro and three Evolv200s! I split the four 600 batteries between me and my partner’s carry on camera bags instead of inside checked luggage to save weight (btw I always put gaff tape over the contacts of the batteries just in case…). All of the stands were rented in Seattle and for the smoke I advance shipped smoke grenades to the Marketing Director. It takes planning folks….LOL
For modifiers I took three v2 Saberstrips which use Evolv200s with their Fresnel heads. I cannot speak highly enough about both the Evolvs and the new Saberstrips. Together they create what I view as a revolutionary combination in camera lighting. Yeah they’re that good. I knew that both the MOPOP and the bookstore sessions would be VERY CRAMPED in terms of space. Using “traditional” modifiers or strobes would be a total pain in the ass. Sure it could be done, but would easily have been a 10/10 on my cussing scale. I knew I wanted a softer light for both the MOPOP and bookstore feeling, but a hard light in the alley. So I took three Fresnel modifiers for that session. All of my modifiers fit into my SKB hard sided golf case which I use to transport my light modifiers when traveling out of town.
So here’s how it all worked: (All of the BTS images are by my partner Tracy Martin)
Session 1, Curious Incident shoot at MOPOP
The Marketing Director wanted an image in MOPOP where the talent appears to be ‘inside’ a dream. So placing modifiers INSIDE this structure for the style of light I wanted to achieve would have been next to impossible without the Evolv200 and the v2 Saberstrip.
One of the final images before editing.
Using the Evolv200 and the Saberstrip to create the feeling of an overhead light source WITHOUT the need for a boom arm is wonderful. Almost all of the other modifiers I own would need to be tilted at an angle to face toward the ground without a boom arm. The Key light is a the Explor600 Pro with a Fresnel head modifier to my right next to the tower structure.
Final shot. Balancing the light to not overpower the hand held flashlight was key for this image. Had I only used the Fresnel pointing at the talent it would not give the impression of an overhead light which was key to this shot.
Session 2 for Matilda at ReRead Bookstore
About 20 people were in this tiny quaint bookstore just for this shoot! I think the actual customers were highly entertained. (They were taking iPhone photos of us! LOL) Here the Marketing staff and the talent review some of the images on my iPad.
Marketing looks over the shots in real time. As you can see the Saberstrip was invaluable in this session. Soft light, yet so good in tight spaces! I love it!!!
Jerry the AD attends to the details. I feel we made a great team since I sometimes miss the small but so important details when I’m in a session.
Ah I cannot say enough about the value of the Evolv200s paired with the v2 Saberstrips!!!!
A few of the Final Images
Session 3 for Howard Barnes in an alley in Everett WA
I laughed as I watched people walking by! They had no idea what to make of what was going on. Oh and that puppet freaked me out!
The Director of Howard Barnes is my light test fella. This is the alley in ‘natural light.’
The talent just yucking it up while I balance the smoke lights. Oh and if you’ve ever worked with smoke it’s great when there’s no wind…..LOL
A few of the Final Images
So cool that wind was coming up from that ground grate so her tail would fly!
Four Xplor600s and two Evolv200s lit this shot. Whew!
I was so shocked to see an article written by James Spangler the owner of ReRead Books where we shot the Matilda publicity! All if not most photographers know that getting feedback is rare so this was both a nice and humbling surprise. My whole point on this post is to highlight the incredible leap in technology and innovation in the field of photographic lighting. Sure all of us can figure out how to do something even if it’s tough. But to have others who are helping to ease the stress of creating beautiful light is wonderful!
Sometimes in my infinite idiotic wisdom I purchase something because I can’t afford something else. I use that item for a while and then it sits on the shelf for a bit. This has been my buying using pattern for quite some time, like I said I can be an idiot.
Such was the case when I purchased a Saberstrip light modifier. I had rented a Westcott IceLight and had a great experience with it, but at $499.00 it seemed a bit too steep in price for a constant light source I would only use occasionally. (I ended up buying two of them later, but that’s for another post.) Like everyone else I began searching the web for alternatives to the IceLight and found the Saberstrip. Unlike the IceLight the Saberstrip uses a handheld flash as its light source.