I realized I had posted some of my lighting techniques under a different blog heading about the v2.0 Saberstrip modifiers, which I consider to be a revolutionary modifier, but had not updated this post. I do so because I find the v2.0 Saberstrips to be almost invaluable for me in creating dance imagery. In some cases I have used three of them to light dancers in studio. As an overhead light on a boom arm and two on each side of the dancers as rim lights. It creates a very dramatic sculpture of their forms as they move. I have also taken to using my 10″ Fresnel to light dancers. I love the light produced by a large lens Fresnel. A hard contrasty light that is unlike any other modifier.
In this image you can see the three v2.0 Saberstrips, my Fresnel (a Hollywood spotlight I converted to a strobe) and my 69″ Elinchrom I converted to a focusing rod modifier.
One of my v2.0 Saberstrips which uses a AD200 as the light.
The following images were all created with three v2.0 Saberstrips as shown in my photo above.
The following were shot with a backlight with a cone, three v2.0 Saberstrips and the Fresnel as a fill light.
And finally two v2.0 Saberstrips and the Fresnel as a key light.
For me experimenting with light is one of the most exciting parts of dance photography. Don’t be afraid to experiment, otherwise all of your images will begin to look the same. And what fun is that?
UPDATE October 12 2017
In my review of Cheetahstand’s Quick Stripbox and Lantern I have shown my lighting setups for a different dance troupe. You can view that post here.
I was recently hired to do an annual studio dance session by one of my long time clients. I’m posting this to show how I use xPLOR, eVOLV, Cheetahstand, CononMark, etc lights and modifiers in a session. This was an all-day session lasting approximately 6.5 hours of nonstop shooting. I had charged both the Xplor and eVOLV lights to full the day before. I never even ran close to running out of battery power on any of the strobes. All of the strobes showed half full at the end of the day. My Canon 1DXII showed 25% battery life left at the end of the day to give you some reference. I was using the WFT-E6A wireless transmitting dongle on my camera to wirelessly tether my rig to my iPad so the client could view the images as they happened. Using the transmitter uses more battery life than without.
There seems to be quite a bit of ‘talk’ that certain brands of modifiers/lights/etc. must be used in order to ‘be a pro.’ Nonsense. How one uses gear, how one engages with the talent and how one uses their imagination are the most important part of imagery to my clients. So I post this in hopes that it will help other shooters who are interested in multi light set ups, but not hung up on brand names or scientific theories about what makes a true parabola or other talking points. When people ask me what is the one thing I would have for gear over everything else, I always say your imagination. Years ago I was blessed to be able to spend time with Annie Leibovitz and I asked her “How do I shoot more like you?” Her response? “Don’t shoot like me Mark, shoot like you. It’s the only way to develop your own style.”
I used a four light setup most of the day. My key light was the CononMark 120cm inverted octa using an xPLOR600 with a remote head. I opted to not use my Parabolix D35 because the size I needed for the day required a larger modifier. And I’ve been very happy with the quality of light from the Cononmark. My two rim lights are Cheetahstand Quick Strip lights using xPLOR600s and the top overhead light is an eVOLV200 mounted into an AD-B2 housing. The modifier is a Fresnel adjustable head. For dance I always use a 140″ wide seamless. In this case I’m using black to give a grittier look to the imagery.
I use children’s ABC flash cards to help me know what light is in what group.
The great thing about battery powered strobes is I can roll the key lights or others wherever they’re needed when I want a different look for light
I had to be creative in sandwiching my eVOLV200 against the ceiling!
I continue to be absolutely amazed at the flexibility and versatility of the v2.0 Saberstrips. As of this writing I do know that Scott has not yet offered these for sale to the general public. The reason I continue to post my findings here is in hopes of motivating some of you to contact him to ‘hurry him along‘ in the sale of these modifiers. In addition to dance, their form factor and quality of light make them invaluable in my tool kit. Seriously – combined with the AD200 strobes I feel they are a revolution in modifiers. Here are just a few of the in studio dance imagery created using these lights.
An AD200 is the strobe.
My general configuration of the v2.0 Saberstrips for this session. The converted Fresnel and the 69″ Elinchrom I have converted to a focusing rod modifier are actually used for FILL, not as key lights for this dance session.
Update November 19 2018
I continue to be so impressed how using two v2.0 Saberstrips can produce the light I so love which could only be created with a ring light. But the huge difference is since the lights are NOT attached to the camera, I can use a long lens, yet keep the lighting near the talent. This was taken with a Canon EF 85mm f1.2 lens. The versatility of these modifiers is incredible.
Not to mention my use of them in dance imagery creation.
Several of you have written to me asking when Scott will release these modifiers. I highly suggest you write to him on his website to ask. I continue to encourage him to release these modifiers.
Update October 14 2018
I recently conducted a studio dance session using three Saberstrip v2.0s combined with a Mole Richardson Fresnel spotlight I have converted to a strobe. I continue to be so amazed and impressed by the versatility and light quality of the second generation Saberstrips. As I’ve stated before I’m just scratching the surface of what can be accomplished with these remarkable lighting tools.
My general placement of the SS’s for the dance session. I am able to control on/off levels using my R2 controller. The ability to place the hair/rim light so close to the ceiling is remarkable.
Here you can see my general placement of the Fresnel spotlight which has been converted to a strobe which uses a Flashpoint 1200ws head.
Each of these images were created using a combination of Fresnel/Saberstrip light modifiers.
Update September 17 2018
Yesterday I conducted an all day dance session. I found that utilizing three v2.0 Saberstrips with 3 Flashpoint AD200s produced remarkable light for studio dance. Rim lights, using two Saberstrips and one overhead light produced the exact mood I was trying to achieve. Seriously this combination is incredible for my dance work.
How I configured the Saberstrips for the dance session.
Update August 1 2018
I recently used the v2 Saberstrips in on location sessions in Seattle. Man I could not have done it without them! You can read about it here.
I have also completed a publicity shoot using two Saberstrips for a West Side Story publicity image as shown below.
Two v2 Saberstrips in parallel to the ground. I just love the look of this light configuration.
Like most other folks and way before I began shooting as a full time pro, I had a day job. It was during this time I discovered a very unique light modifier called the SaberStrip. What was so intriguing to me is its shape and the quality of light it produces. I was a bit suspicious when I first received my Strip because it seemed like ‘just a high quality shipping tube’ with some rip stop nylon as the modifier’s cover. Also this was back in the day when I was almost exclusively using speed lights, but had two PCB Einsteins for my ‘studio work.’ And this was well before the advent of built in radio receivers in speed lights, so I had to use a pigtail cable connected to my speed light inside the tube to attach it to the Phottix Transmission receiver I was using at the time. A bit of a hassle, but it was the only thing that existed at the time, which was ‘high tech’ for that era.
Although I loved the quality of light it produced, for me the power or rather lack of power of the speed light relegated the Strip to my closet. I tried to fabricate my own ‘Strip’ for my Einsteins, but found out it was not as easy as I thought. So I basically gave up and moved on to other things.
In 2013 I decided to create a series of images about the hands of artists which included both performing as well as creating artists. Since I wanted to shoot the talent in their natural environments I found that all of my ‘normal’ modifiers would not work well due to space. In some cases I had literally 10 inches or less to place a light and modifier to light the talent! So as I was rummaging through my gear closet I happened upon my Strip that I had doomed to its lonely existence in the back of my modifier closet. Eureka! That’s the perfect tool for this job and since most of the venues I was shooting in were very small I would not need a ton of light power so my speed light would do just fine.
By happenstance the Director of the Peninsula Museum of Art saw one of my images and asked to see the rest. She then asked if I’d consider having a solo exhibit at the museum the following year. I politely told her no and when she inquired as to the reason for my decision I simply replied “I don’t think my work is good enough for a museum and I think it would be very narcissist to do that.” She simply smiled and said OK. Later one of the artist I know mentioned that he had heard I was offered a solo museum exhibit but turned it down. Werner asked me if I ever go to museum exhibits to which I responded “Why yes, I love going, why?” His response was typical Werner, direct and to the point; “Well quit being so fucking selfish and let others enjoy and be inspired by what you’ve created Mark!” I’m seldom if ever at a loss for words but I had nothing to say. So I contacted the Director and agreed to display my work which I titled “29 Hands, 15 Artists.” With the exception of one of the images, all were lit with my Strip and a speed light.
Fast forward to today, 2018 and I was made aware of SaberStrip’s v2.0 version of the Strip which accepts an eVOLV200! In March 2018 I was shipped two advanced copies of the modifiers to test to see if I could offer any feedback. Here’s what I’ve found so far:
The 200 is inserted into the bottom of the modifier through what I call the “Tractor Tire” the designer fabricated it to attach the 200. I believe his design is to offer strength to the mount. I simply like to think he liked Tonka Trucks as a kid! The knurled knob on the left in this photo is the turning knob that screws the 200 in place. The other nice design feature is you can eject the battery of the 200 without removing it from the modifier, a very thoughtful design element.
Sorry for the shitty camera phone blurry image. The red thing you see at the top of this shot indicates that the screw is NOT attached to the 200 which is a very nice feature. One of the things that I found to be a design issue, it’s very easy to over tighten the screw. There’s no need to do so because it makes it VERY difficult to unscrew the unit from the mount. I learned the hard way and had to use a screwdriver and hammer to loosen the screw.
It’s also not possible to let the eVOLV slide down into the tube because there are ribs on the interior which keeps the strobe from sliding too far into the unit. I believe he may have other plan since those interior ribs seem to be reinforcements for four exterior metal nipples. Barn door or grid accessories for the future? Perhaps.
I painted a directional arrow on the housing to indicate which direction to loosen the mounting screw.
What the interior looks like in the v2.0 Strip. You can see the reinforcing supports which prevent the eVOLV from sliding too far into the tube.
Although most people will not have to do this, I ground down the mounting peg that is cast into the housing. This allows me to easily insert the peg into female mounts I use to place the modifier in either a vertical or horizontal position. Although the v2.0 Strip works extremely well in stands which offer the mounting peg to be in a vertical or horizontal position, not all light stands offer that option. When I travel to other cities I often have to rent stands and not all rental houses have adjustable spigot locations on their stands.
This is why I needed to shave down the diameter of the molded peg. It would not fit as cast. I find these female spigots invaluable in my gear bag.
I plan to use these to mimic a ‘ring light’ because I can now leave the modifier and strobe very close to the talent and back away to shoot with a long lens. Not possible with traditional ring lights. Also since the eVOLVS have modeling lights in the Fresnel head I now have a modeling light in this configuration. Sure, not brightest modeling light, but way better than none.
My first test was with Bob outdoors for a ring light style lighting test.
Canon 1DXII EF135 lens ISO 100 both AD200s set at 1/8 power. 1/5000th f2.0
Canon 1DXII EF135 lens ISO 100 both AD200s set at 1/8 power. 1/8000th f2.0
In those instances where I want to place the v2.0 Strip close to the ground I will simply use a Godox S bracket as a base. This configuration will be perfect for dance shoots as fill lights or anytime you wish to place the units very low onto a flat surface.
w/2 eVOLVS and SS
Flashpoint Zoom R2
Distance to Sekonic
Time to Recycle
Length of fabric
Width of fabric
Length of modifier
Diameter of modifier
For me the most significant stats are the recycle time and power. It’s the very reason I stopped using my original speed light Strip, it just lacked power. And in my work a one second delay feels like 12 years. Human expressions change in a nanosecond and invariably it’s the money shot I wanted, but missed because the strobe was recycling. Two full stops and five seconds faster in recycle time makes this modifier an incredible tool.
The ‘tube’ freely rotates around the mount so it can easily and conveniently turn the fabric to any position needed. There’s also a very small 1/4 inch 20 screw hole in the ‘tractor tire’ housing. I’m not sure why the guy put one there but it’s damn convenient. I plan to place a female mounting stud in there so I can either mount the Strip with the built in male stud or a female one. It should be noted that if you place a long ¼ 20 screw into that hole it will stop the free rotation of the tube. So IF you are the anal type and want to lock down the tube’s rotation you can do that with this screw hole.
This coming weekend I have three personal project shoots and I plan to test the light quality and applications in those sessions. I’m not sure how many times the Strip v2.0 will be my key light, but now that the recycle times and the power available through this meets my needs I’m sure it will always be in my bag.
The number of ways to mount the Strip seems endless. My current favorite grip mount for the Strip is the Matthews Mini Grip Head. I modified it by drilling out one of the holes to 9/16th of an inch which fits the Strip’s 5/8th inch stud.
What I like:
High quality Construction
Built in male mounting stud
Ability to rotate the modifier around two axis
Accepts the Evolv200
Well balanced, having the strobe at the mounting end of the modifier
Very wind resistant
Will fit into very tight spaces
Male stud needs to be the 5/8th inch size standard of all spigots
Wheel that attaches the strobe needs to have directional arrows.
Wheel needs to prevent over tightening
During the weekend of April 21st 2018 I had my first opportunity to use the v2 Sabers in studio. I wanted to determine if paring them in a horizontal way would give me the ring light type of affect. I’ve always loved the look of a ring light shot, but have been frustrated that the distance of the light to the talent is limited by the focal length of my lens. Using my ring light further away to compress the talent’s face meant that the light is also further away, causing a harsher look. But using two Strips horizontal to the ground with the ability to adjust the distance between them allows me to leave the light source close to the talent, yet move further back to use a longer focal length. Having my cake and eating it too is wonderful!
The images below show how this worked on Jessica and I’m very happy with the results. Shot with a 135mm prime lens.
The flexibility of being able to angle the pitch of the Strips and distance between them is wonderful. More control than a ring light. As a fill/rim light I have not experienced a better modifier. Reflectors make great fill or rim light modifiers, but I have always preferred strobes for that task. It allows me finer control of my fill light.
By changing the angle of the top Strip in the image of Jess with her arm above her head I am able to cast a bit of a shadow on her eyes while filling in under her eyes to prevent shadows. That flexibility allows me to create nuance shadow/highlights with the Strips.
Here I am using the Strips as a fill and rim light. All of these images are three light shots. My 10” Fresnel is the key light, a gobo modifier is used on a light to create pattern on the background and the Strip is used as a fill/rim light.
The control of the Strip as a fill light is quite lovely and can be used as subtle or as bold as you wish. Here are two more images I created using two SS’s in parallel as a ‘ring light’ but in my view with a much better result.
Erica is 50+ and just the use of a shallow DOF and the two SS lights produced this image WITHOUT the use of Photoshop.
Two SaberStrips v2.0
Three SaberStrips v2.0
Oh and large groups in moderate to strong wind? I was recently at a client to cover the high school musical awards and prior to the event kids assemble outside. It’s often a fun place to get group shots before the show. The issue is always crowded sidewalks and of course crazy high school kids. I shot this image with ONE SS and one eVOLV200 at HALF POWER.
1/100th f5.0 ISO100, SS v2 is the modifier and the strobe is the AD200 set to half power. Can you say incredible? It’s crazy.
I recently visited Luna Cycle in El Segundo to do some documentary photography of the staff. In the vast majority of cases the SS were used due to their flexibility and light quality. As in my 29 Hands Exhibit I was able to use the SS to light the talent in places where it would be almost impossible to fit a modifier in the space I had available and achieve a quality of light I wanted. Below is an example of one of the shots.
This is the ‘natural light’ scene where I was to photograph one of the young ladies who performs logistics for Luna Cycle.
Removing some of the boxes and shooting the light through the bookcase produced the image and quality of light I was after.
My apologies as I know you won’t be able to ‘unsee’ the image that follows, but to date it illustrates the rim lighting capabilities of the Strip. During this session I was to shoot two Drag Queens. The fella on the left is 6-1 without heels and with his 4” heels it makes him 6-5! I used the Strip as a rim light and if you notice the illumination from head to toe it’s quite remarkable. Could this be accomplished with a gridded light? Of course it could. But due to the very slim shape of the Strip it allowed me to get as close to the back drape as possible keeping spill to a minimum and certainly much less than a softbox without a grid.
Outdoors with the Strip is quite good. It is ‘almost’ impervious to wind, high wind. It is more wind resistant than my go to outdoor modifier, the PCB Omni. The disadvantage is since the Strip uses the AD200 it is a full stop less powerful than the AD600 I use with the Omni or my Aputure Fresnel head. But to circumvent that disadvantage I often use two Strips as a key light when outdoors. And in those instances where I want a very large light source I use three Strips configured in a Y shape. I find it’s the equivalent to a 45” octa with 600ws of power. Ever use something that size out in moderate or high wind? And I use all three on a single stand.
My partner recently conducted a head shot session using two of the Strips. She used one as the key and the other as a rim light. It was very windy under the concrete bridge where she was shooting and the Strips barely wobbled. The light quality is excellent and easily replicated her preferred modifier, a Glow 36” Octa. But in that kind of wind, especially the gusts that occurred an octa would have been quite the handful. She does prefer the catch light of the octa, a personal preference to which many people may agree. I happen to feel that round catch lights are the default, yet in natural light a catch light is anything but round…..
As you can see the quality of light produced by the Strip is excellent. Two lights, both Strips. One as the key light the other as a rim light.
Is it the perfect modifier? Nope, but as of right now there is no perfect modifier. Just like there’s not a perfect camera, lens or person. Is it the most versatile modifier I currently own or use? YES! For me the v2 Saber Strips are revolutionary and I have not even scratched the surface of how they can be used. Thank goodness for the AD200 lights and Scott’s development to incorporate them into the Saber Strips! Scott has mentioned that the v2 versions which use the eVOLV200s will be available in late July 2018.
People always get so nervous when they see how I hold my cameras! I hate straps. LOL!!!
Shooting as a pro means there are times when you have to prove yourself once again with an established client. Not doing a great job either in the finished product or through your service simply means you’re not used again. One of my long standing clients, Village Theatre recently changed Artistic Directors. Jerry Dixon, their new AD planned to attend two of the three on location publicity shoots all to be held in different cities in greater Seattle area. The first session for the play Curious Incidents is also the play he is directing. No pressure eh? LOL
The second aspect of this day that is always a bit concerning was that I NEVER SAW ANY OF THE VENUES IN ADVANCE of the day! Sure the Marketing Director sent me some camera phone photos and links to the MOPOP (Museum of Pop Culture) areas where she wanted to shoot, but I had never been there. Nor had I been to Spangler Book Exchange/Reread Books, the quaint bookstore where we were to shoot the Matilda publicity or the alley in Everett where I’d shoot the Howard Barnes publicity. Add to that the additional element of time. For each venue we were limited in time based on either the schedule of some of the talent or due to the venue’s prior commitments.
The only element I ever insist on from clients is to answer; “What is the mood you want from each session?” Why? Well because the expression of the talent(s) and the LIGHT is something I have to plan for BEFORE I hit the job….which leads me to….
The Marketing Director kept asking me “Mark, I need to know your power requirements for each venue so I can work with each of the operations managers to plan power for your gear.” Since I exclusively use Flashpoint strobes, guess what….they need no outside power!!! SCORE! I hauled seven, yes seven strobes from SF to SEA in a small Pelican case. 49.5 pounds…just UNDER the 50 lbs. limit! Three Xplor600s, one 600Pro and three Evolv200s! I split the four 600 batteries between me and my partner’s carry on camera bags instead of inside checked luggage to save weight (btw I always put gaff tape over the contacts of the batteries just in case…). All of the stands were rented in Seattle and for the smoke I advance shipped smoke grenades to the Marketing Director. It takes planning folks….LOL
For modifiers I took three v2 Saberstrips which use Evolv200s with their Fresnel heads. I cannot speak highly enough about both the Evolvs and the new Saberstrips. Together they create what I view as a revolutionary combination in camera lighting. Yeah they’re that good. I knew that both the MOPOP and the bookstore sessions would be VERY CRAMPED in terms of space. Using “traditional” modifiers or strobes would be a total pain in the ass. Sure it could be done, but would easily have been a 10/10 on my cussing scale. I knew I wanted a softer light for both the MOPOP and bookstore feeling, but a hard light in the alley. So I took three Fresnel modifiers for that session. All of my modifiers fit into my SKB hard sided golf case which I use to transport my light modifiers when traveling out of town.
So here’s how it all worked: (All of the BTS images are by my partner Tracy Martin)
Session 1, Curious Incident shoot at MOPOP
The Marketing Director wanted an image in MOPOP where the talent appears to be ‘inside’ a dream. So placing modifiers INSIDE this structure for the style of light I wanted to achieve would have been next to impossible without the Evolv200 and the v2 Saberstrip.
One of the final images before editing.
Using the Evolv200 and the Saberstrip to create the feeling of an overhead light source WITHOUT the need for a boom arm is wonderful. Almost all of the other modifiers I own would need to be tilted at an angle to face toward the ground without a boom arm. The Key light is a the Explor600 Pro with a Fresnel head modifier to my right next to the tower structure.
Final shot. Balancing the light to not overpower the hand held flashlight was key for this image. Had I only used the Fresnel pointing at the talent it would not give the impression of an overhead light which was key to this shot.
Session 2 for Matilda at ReRead Bookstore
About 20 people were in this tiny quaint bookstore just for this shoot! I think the actual customers were highly entertained. (They were taking iPhone photos of us! LOL) Here the Marketing staff and the talent review some of the images on my iPad.
Marketing looks over the shots in real time. As you can see the Saberstrip was invaluable in this session. Soft light, yet so good in tight spaces! I love it!!!
Jerry the AD attends to the details. I feel we made a great team since I sometimes miss the small but so important details when I’m in a session.
Ah I cannot say enough about the value of the Evolv200s paired with the v2 Saberstrips!!!!
A few of the Final Images
Session 3 for Howard Barnes in an alley in Everett WA
I laughed as I watched people walking by! They had no idea what to make of what was going on. Oh and that puppet freaked me out!
The Director of Howard Barnes is my light test fella. This is the alley in ‘natural light.’
The talent just yucking it up while I balance the smoke lights. Oh and if you’ve ever worked with smoke it’s great when there’s no wind…..LOL
A few of the Final Images
So cool that wind was coming up from that ground grate so her tail would fly!
Four Xplor600s and two Evolv200s lit this shot. Whew!
I was so shocked to see an article written by James Spangler the owner of ReRead Books where we shot the Matilda publicity! All if not most photographers know that getting feedback is rare so this was both a nice and humbling surprise. My whole point on this post is to highlight the incredible leap in technology and innovation in the field of photographic lighting. Sure all of us can figure out how to do something even if it’s tough. But to have others who are helping to ease the stress of creating beautiful light is wonderful!
A trombonist and his PR rep flew in from Nashville, TN to conduct two day photo sessions for his upcoming CD release in the Fall. We had spoken over the phone and via email about the theme for his shoot. I didn’t feel that a traditional musician with instrument would suit his personality. Nor did I believe it would show any creativity, so we agreed on two separate sessions. One on location and one in studio.
Day one was conducted on location at Ocean Beach in San Francisco just before sunset. During his trip it was the only day when rain was not forecast which meant IF the weather people were correct, the sky would have wonderful clouds, one of my favorite elements for outdoor sessions. As luck would have it, the sky and weather were perfect…whew!
BTS shot. Here I used one AD-B2 with two eVOLV200s shot through an adjustable Aputure Fresnel Lens as the key light. Another single eVOLV200 using its included Fresnel head was used to augment illumination of the fire/cello/violin fire.
For each shot on both days I used a total of six different modifiers, but only two different strobes. xPLOR600s, and eVOLV200s. Using AD-B2 and 600ws extension heads gives me flexibility like no other system. It’s one of the big reasons I have switched over to this system.
Two eVOLV200s mounted in a single AD-B2 shot through an Aputure Fresnel modifier was the key light. A single eVOLV200 using its native Fresnel head and barn doors with gel was used to augment illumination on the fire/cello/violin bonfire. Canon 1DX Mark II 1/400th.
Canon 1DX Mark II 1/400th using two eVOLV200s inside the AD-B2 shot though the Aputure Fersnel head.
Day two was shot in studio using four different modifiers on four xPLOR600s, two using remote heads. The modifiers were:
An Adorama GlowPop 38 with both inner and outer diffusion panels as a rim light
An Andoer Metal Conical Snoot on a boom to illuminate the martini glass with mini trombone
A Cheetahstand 40 inch (100cm) QS40 Silver Beauty Dish with diffusion panel installed as the model’s leg light
Although I use a wide variety of modifiers from many different manufacturers I only use Flashpoint/Godox strobes. Why? Well because their performance, value, quality and flexibility gives me options that I’ve not been able to find anywhere else. The battery life of either of those units is incredible. I have yet to exhaust the battery during an all day session.
My goal was to create the illusion of a stage, a grand hall using light, shadow and atmosphere. This was the very first time I used every single Godox light I have including a speed light. What is wonderful is how seamlessly all of the lights integrate into a system. I could not be happier with this line of strobes.
All shot with a Canon 1DXII, EF24-70 II. Most images shot at 1/500th at various f stops, ISO 100. I have quite a few reviews of the gear I sighted above. The purpose of this post is to simply show how I use the gear rather than update each review. I find actual usage much more helpful for me and hope this helps you as well.
The warehouse where I ran this session. The chandelier was borrowed from a theatre company. It is lit with an xPLOR 600 using a PCB Retro Laser modifier (no longer made) which is out of frame. The light to the left is to illuminate the talent using a 1200ws head and a Fresnel modifier.
Four xPLOR 600s, two powering the 1200ws head, one placed into a Parabolix 35D and one in the PCB Retro Laser modifier.
Cheetahstand Lantern as top light using two eVOLV200s in an AD-B2, Parabolix 35D camera right. Speed light rigged into the umbrella.
You can see how I rigged the speed light into the umbrella. I fabricated the handle since this is just a cheap photographic umbrella.
My fantasy composite of combining her image and a shot I captured along the Oregon Coast. When I created her umbrella image I had planned on working it into a composite, so I knew how I wanted the light/shadows to match the scene.
Two Fresnel heads. Parabolix camera right, low and fully focused.
Two Fresnel heads. Parabolix camera right and fully focused.
Two Fresnel heads. Parabolix camera right and fully focused.
Two Fresnel heads. Parabolix camera right and fully focused.
Oops, forgot to turn off the smoke machine again!!!!